If the WPS indicator on your Verizon router is blinking blue, you can begin the pairing process. That could be due to a connectivity problem, or it could be because you accidentally pressed the WPS button (which is located on the front panel of the router).
Your Verizon router’s blue light will blink for no more than two minutes before going solid blue, indicating a successful pairing with a WPS-enabled device.
If your device continues to flash blue for longer than that, it may be stuck in pairing mode or experiencing technical difficulties.
The blue light on your FiOS router could be signaling a number of potential issues. The following are some of the most frequent:
- Pairing mode is currently being performed on your router.
- The router is attempting to make contact.
- The router is overheating and it’s causing problems.
- There must be a firmware update for the router.
With that out of the way, let’s go over some potential answers. Check out each of these suggestions. And rest assured that by the time you finish reading this article, the blue light on your Verizon phone will no longer be flashing.
1. Restart Your Verizon Router
You should try restarting the device as a first step. This should be the only stage at which you need to worry about the blue blinking light. The situation is the same when the Verizon router lights up in yellow.
How to Restart a Verizon Router
- Remove the power to the router and turn it off.
- Be sure to remove any backup batteries as well.
- Hold on for a minute or two.
- Turn the router back on, and plug in the backup battery.
- Hold off until the router has started up.
- At long last, the Verizon router’s white light indicates a successful connection.
2. Power Cycle Your FiOS Router
This method, like routine rebooting, makes sure the router has no residual power. The hardware in the router will be restarted when you turn it back on, resulting in improved performance.
How to Reboot Your FiOS Router:
- Put the router to sleep by pressing the power button.
- Just give me a minute.
- Remove the cord from the switchboard now.
- Just give it another minute and a half.
- Then, disconnect the router’s power source completely.
- Just give it a minute or two.
- After that, connect each end of the cable and power on the router.
- Patiently wait for the Verizon router to finish booting and the lights to stabilize.
The Verizon FiOS router’s blue blinking light is probably no longer blinking at this point.
3. Check for Maintenance or Internet Outage
If your FiOS router is blinking blue, it could be due to routine maintenance or an interruption in service from your provider.
How to Determine if There Is an Internet or Maintenance Outage:
- For servicing inquiries, please get in touch with your regional dealer.
- Expect an official statement regarding the disruption in service.
- There isn’t much you can do if an outage or maintenance is preventing you from accessing the internet.
4. Inspect Cables & Wall Jack Of Your Router
Problems with connectivity can be caused by a number of factors, such as a loose cable or moisture in the router’s ports or wall jack.
Methods for Examining Cables
- Verify the integrity of each cable and wall jack.
- Make sure there is no wiggle room and that they are completely dry.
- If you keep seeing the blue light, it’s a good idea to check for a short circuit or damaged wiring.
- Clean the ports and cables with a microfiber cloth.
5. Check Your Device for Overheating
The Verizon hotspot indicator light may flash blue if it gets too hot. If so, unplug the cable router and give it five minutes to cool down before reconnecting it to power.
If the problem still persists, reconnect it and turn on the router.
Methods to Keep a Router Cool:
- Make sure there is no dust anywhere near the router.
- Keep clutter away from the router by putting it lower.
- Make sure there is enough room around the router for it to breathe.
- Keep the router away from any heat sources such as stoves, microwaves, and other ovens.
6. Check Your Verizon Router for Overloading
It’s possible that your Verizon router is overworked if the blue light keeps blinking. This may occur when more data is being sent or received than the router can handle.
Overloading your modem or router? Try these steps.
- Turn off the router and any unnecessary gadgets.
- Limit the amount of simultaneous WiFi users.
- In the event that this problem still exists, you will need to upgrade to a compatible third-party wireless router with Verizon FiOS.
- And if your home has more than two stories, a mesh Wi-Fi system that is compatible with FiOS is the way to go.
7. Update Your Router Firmware
Did you try what I suggested above, but the blue light still persisted? Perhaps new firmware is available for your router.
How to Perform a Firmware Upgrade on a Router:
- Access the router’s administration page.
- Navigate to the Settings menu for your computer.
- New software should be downloaded and installed whenever possible.
- Then, after the router has restarted, see if the blue light has disappeared.
8. Test a Wired Connection With Your Router
Eventually, the router’s wireless connection will stop working, so testing the wired connection is the best bet.
How to Check a Hardwired Connection:
- You should unplug everything and inspect the wires for dirt and damage.
- Ensure that the router’s internal ports are clean by blowing them out if necessary.
- Carefully swap out the faulty wires.
- Restart the router after you’ve reconnected all the wires and cables. Check to see if you’re back online.
9. Try Factory Reset Your Verizon Wi-Fi Router
If nothing else has helped, resetting the FiOS router to factory settings is the next logical step.
All of your current settings will be lost as well. As a result, always have a backup ready in case you lose the original.
How to Perform a Hard Reset on a Router Using the Settings:
- Connect to the router’s web interface.
- Go to the More Advanced menu.
- Next, select Save & Restore from the Utilities menu.
- To complete the process, select Factory Default > Restore configuration.
Another straightforward option exists for resetting the FiOS router to factory settings.
Using the Router’s Reset Pinhole, Perform the Following Steps:
- Take something like a paperclip or a pin.
- For the router’s reset button, press it for 10 to 15 seconds.
- In a few minutes, your router will reboot and your internet will be back up and running.
- At long last, give it a shot to get online.
10. Contact Support
The last thing to do is to get in touch with a repairman. He’ll take a look at the router and let you know if it’s broken beyond repair or the scope of the warranty.
Also, if you’re able to do so, I recommend purchasing your very own FiOS router and doing away with those pesky monthly fees.
In addition to avoiding these complications, it will also improve your speed, range, and management options.
Frequently Asked Questions
What does the blinking blue light mean on a Verizon router?
If your FiOS modem is flashing blue, that means it’s in WPS pairing mode, trying to connect to your wireless network. If the link is established, the light will turn white. If not, you may need to perform some troubleshooting.
How to check the Verizon internet outage?
If you need information about internet outages, you can get in touch with your regional distributor. You’ll need to check back for updates if and when maintenance becomes an issue.
How to restart the Verizon router?
Turn off the modem/router and unplug the power cord. Please hold off for a moment before turning it back on.
The Verizon router’s blue light flashing is a common problem. Your problem-solving options are, thankfully, tried and true.
The simplest way to restore normal operation is to reboot the router. In the event that this strategy does not work, try one of the alternatives described above.